Refit  1/350 Enterprise Drydock Startup Sequence Lighting Set

$179.00 + $10.00 shipping in the U.S.

Click Picture!

$179.00 + $18.00 shipping worldwide

 

This new lighting kit comes with everything you need to illuminate your 1/350 scale USS ENTERPRISE NCC-1701(Refit) model. It features our new Refit Enterprise 1701 Drydock Startup Sequence FX Board. It's function was designed to mimic the famous drydock startup sequence from ST:TMP right before the Enterprise was depicted to leave the drydock in Earth orbit.

The board measures 2.5" x 1.6" (6.4mm X 4.1mm). It is a pretty small board with a low profile, designed to fit in the forward most chamber of the secondary hull belly area, right above the botanical garden guide pin. However, it can also be installed in your display base.

It works with two (2) momentary push button switches. The first switch activates "Mode 1" which is the actual startup sequence. The sequence begins with the windows or ambient interior lighting, thrusters and torpedo tube static lighting. It goes through the entire cinematic sequence as seen in the movie and ends up in 'impulse mode' with the impulse engines ramping up 5 seconds later.

The second switch activates "Mode 2" which is 'warp mode.' The orange/amber deflector, orange/amber impulse crystal, and impulse engines all ramp down and the blue deflector, blue impulse crystal, and blue warp nacelles ramp up in their place. When the second switch is pushed again, it switches back to impulse mode, all while the floodlighting, strobes and running lights remain on, as per the movie.

It runs on 9V-12V DC 2A(or more) and works very well with high power SMD strips. This board comes pre-assembled and ready to use. Just connect your LEDs in the proper order to the terminals on the board and you'll have the effect that you see in the video demo. The board comes with (2) pre-wired RGB LEDs, 150ft of flat ribbon cable,  (2) momentary switches,  (2) pairs of plug and headers for easy connection to the terminals. (4) 5mm white LEDs, (2) 5mm amber LEDs, (8) 3mm white LEDs, (4) 3mm warm white LEDs, (2) flat red LEDs, (2) 1.8 mm red LEDs, (2) 1.8mm green LEDs, (25) 1.8mm white LEDs. (70) resistors, Hook up wire for the display base, 4ft black wire, 4ft red wire, 4ft yellow wire, 4ft brown wire,  13ft Heat shrink tubing, DC power jack, 48 inches of SMD light strips(white), 20 inches of High density Blue SMD light strips. Comes with everything you see in the picture above. Instructions are simple and well illustrated, in color, and will be emailed to customers as a printable PDF document.

This board was designed to fit within the 1/350 scale Polar Lights Refit Enterprise model kit. However, the effects may be adapted to the smaller Refit model kits such as the 1/537 and 1/1000 scale versions and will fit in your display base.

 

      

 Features

  • Instruction Guide - Well illustrated color guide will be emailed as a printable PDF document to customers

  • FX board simulates 'impulse mode' and 'warp mode' and drydock sequence of ST:TMP

  • Accurately timed flashing strobes and blinking formation lights, as shown in the demo video

 

  • FX board is small enough to be hidden within the model or the display base

  • FX board can be adapted to fit the 1/350, 1/537, and 1/1000 scale Enterprise models

  • LEDs resistors, hook up wire, heat shrink tubing, switches, connectors

 

 

 

NOTE: Power supply not included!

             

             THIS BOARD INCLUDES ACCURATELY TIMED FLASHING STROBES AND BLINKING NAVIGATION LIGHTS PROGRAMEMD INTO IT. THERE IS NO NEED TO PURCHASE A SEPARATE FLASHER BOARD TO COMPLETE THE EFFECT!

This board has the ability to power up the entire 1/350 scale Refit Enterprise model!